An independent reference about smart devices at home. We do not sell or install equipment and are not connected with the former site on this domain.

Problems

Troubleshooting

A smart home acts up for very down-to-earth reasons: a weak signal in a far room, a changed network password, a flat battery, a scene with the times mixed up. Nearly all of this can be fixed calmly without calling anyone out. Here are the typical situations and the steps worth working through in order before you reset a device or write it off.

Before resetting a device, check the socket, the battery and the router: they are the usual culprits.

— Editor's note

How this section works: situations and likely causes are described in general terms. There is no need to open the casing or touch the wiring: if the problem is the socket or the wiring, call an electrician.

Common situations

The device shows as offline.

Check that it has power and that its indicator light is on. Then see whether the internet works on your phone over the home network. If the device is far from the router or hub, bring it closer to test: the signal may simply not reach. Restarting the router and the device itself fixes many of these cases.

A scene does not run.

Open the scene and read its conditions as if you were a stranger: are the right device, time and days of the week selected, is there an extra condition such as "only if nobody is home"? Check that every device in the scene is online. Many apps keep an event log that shows what actually happened.

Commands are carried out with a delay.

If the device is controlled through the cloud, the delay can depend on your internet quality and on how busy the manufacturer's servers are. Check the signal in the room, restart the router and see whether too many devices are connected to the network. For frequent and important actions, local scenes are more convenient.

Everything disappeared after changing the router.

Smart devices remember the name and password of the old network and know nothing about the new one. The simplest way out is to give the new network the same name and password as before. If that is not possible, the devices will have to be reconnected through the app, and sometimes reset according to the instructions.

A sensor triggers for no reason.

A motion sensor can react to glare from the sun, a radiator, curtains moving in a draught and pets. Move it or lower its sensitivity in the settings. A door sensor often gets it wrong if its two halves have shifted and no longer sit snugly together.

Batteries drain quickly.

Check that the batteries are the type stated in the specifications and that the sensor is not somewhere cold. Frequent polling, a weak signal and constant triggering also shorten battery life. If the sensor is far from the hub or router, try moving it or the hub.

If a device has vanished from the app

  1. Check the account

    Make sure you are signed in to the app with the same account the device is linked to. In families it often turns out that someone else added the device from their own phone.

  2. Update the app and your phone

    An outdated app sometimes stops seeing some devices. Install the update from the official app store and restart the app.

  3. Restart the device

    Unplug the device or take out the battery, wait a little and switch it back on. If it works through a hub, restart the hub too.

  4. Check the home network

    See whether the network name or password has changed and whether the router has started restricting new devices. Sometimes it is enough to turn the home network off and on again on the router.

  5. Add the device again

    If the device still doesn't appear, delete whatever is left of it in the app, reset it following the manufacturer's instructions and add it as a new device. Then assign its name, room and scenes again.

  6. Contact support

    When nothing helps, write to the manufacturer's support through the official website or the app. Describe what you have already tried: that way the reply comes faster and is more accurate.

  • Guides

    Step-by-step advice: your first plug, motion-activated lights, leak alerts, guest access for the family. The article catalogue lives here too.

  • Tools

    What to gather before buying and setting up: a task list, a sketch of rooms and sockets, a guest network, a password store and device manuals.

  • Comparisons

    Direct Wi-Fi connection or a hub, cloud or local control, one ecosystem or devices from different makers.

  • Security

    Default passwords, cameras and recordings, microphones, guest access, overloaded plugs, selling and moving without strangers in your account.

  • Glossary

    A plain-language glossary: sensor, scene, automation, hub, cloud, local control, ecosystem, guest network.

Sources

  • Device manuals and specification sheets from manufacturers (in general terms)
  • Security recommendations for home network devices (in general terms)
  • Editorial materials of the Proshivki All guide

The texts in this guide are written in general terms and reflect the editors' view as of the date they were prepared. Smart devices from different makers are set up in their own ways, and buttons and menu items in apps get moved and renamed from time to time. If your device's manual or specification sheet tells you to do something differently from us, trust it.